Operation Instruction

Master Code

The master code consists of a four-digit number and is used to access programming functions of the reader and cannot be used to gain access i.e. It cannot be the same as other PINs. The default master code is set as 1234. Under normal operation the keypad is used for entering PIN to gain access. In the programming mode the keypad can be used to add/delete PINs, set relay strike time and other operation functions

Enter Programming Mode

Enter the master code twice (1234 1234) to enter programming mode (1 long beep, Right Yellow LED stay on).

Set the Access Mode

The dual identification feature allows the reader to be programmed to grant access with either Proximity Card only, Proximity Card or PIN, Proximity Card and PIN.

1. Enter programming mode

2. Press*0 (Right Yellow LED rapid flash)

3. Press 00 (1 beep,Right Yellow LED stay on) for Proximity Card Only Press 01 (1 beep,Right Yellow LED stay on) for Proximity Card or PIN Press 02 (1 beep,Right Yellow LED stay on) for Proximity Card + PIN

4. Press # (1 beep) back to standby mode (Right Green LED stay on

Set the Relay Strike Time

The relay strike time determines the amount of time that the door remains unlocked after a valid proximity card or PIN is entered. Note : For both Relay 1 & Relay 2, enter 00 wil set relay strike time to 0 second (relay set to toggle mode).

1. Enter programming mode

2. Press *1 for Relay 1 (Right Yellow LED rapid flash) Press *5 for Relay 2 (Right Yellow LED rapid flash)

3. Press 00~99 (1 beep,Right Yellow LED stay on)

4. Press # (1 beep) back to standby mode (Right Green LED stay on)

Clear Memory of All Proximity Cards and PINs

1. Enter programming mode

2. Press * 8 (Right Yellow LED rapid flash)

3. Press 88 (No LED , 1 long beep, right Yellow LED stay on)

4. Press # (1 beep) back to standby mode (Ridht Green LED stay on)

Reset Controller Parameter to Default Value

1. Enter programming mode

2. Enter *8 (Right Yellow LED rapid flash)

3. Enter 99 (Both left & rigth Yellow LEDs stay on, 1 beep) back to standby mode (Right Green LED stay on)

Add a Proximity Card and PIN to Relay 1

a. Note : Master code must NOT be the same as PIN codes.

1. Enter programming mode to select slot position 000~999 (Left Green LED stay on, Right Yellow LED rapid flash to indicate the slot position is available)

2. Read new card (1 beep), then press 4-digit PIN 9999 (1 beep, Right Yellow LED stay on).

3. Press # (1 beep) back to standby mode (Right Green LED stay on)

b.-

1. Enter programming mode to select slot position 000~999 (Left Red LED stay on, Right Yellow LED rapid flash to indicate the slot position is unavailable)

2. Press * * (1 beep) to delete the data from the slot position (Left Green LED stay on, Right Yellow LED rapid flash)

3. Press # , back to satndby mode

4. Repeat the steps of 7-a to add new cards.

Add a Proximity Card and PIN to Relay 2

a.-

1. Enter programming mode

2. Press * 4 to select slot position 00~09 (Left Green LED stay on , Right Yellow LED rapid flash to indicate the slot position is available)

3. Read new card (1 beep, Right Yellow LED flash)

4. Press # (1 Beep) back to programming mode (Right Yellow LED flash)

5. Press # (1 Beep) , back to satndby mode

b. -

1. Enter programming mode

2. Press * 4 to select slot position 00~09 (Left Red LED stay on , Right Yellow LED rapid flash to indicate the slot position is unavailable)

3. Press * * to delete the data from the slot position (1 beep, Left Green LED stay on, Right Yellow LED rapid flash)

4. Press # , back to satndby mode

5. Repeat the steps of 8-a to add new cards.

Change Master Code

1. Enter programming mode

2. Press * 3 (Right Yellow LED rapid flash)

3. Enter 4-digit master code twice e.g. 4567 4567 (1 beep, Right Yellow LED stay on)

4. Press # (1 beep) back to standby mode (Right Green LED stay on)

Add a New Master Card to Relay 1

a. -

1. Enter programming mode

2. Press * 7 (Left Green LED rapid flash, Right Yellow LED rapid flash to indicate the slot position is available)

3. Read new card to set as Master Card (1 beep, Right Yellow LED stay on)

4. Press # (1 beep) back to standby mode (Right Green LED stay on)

b. -

1. Enter programming mode

2. Press * 7 (Left Green LED stay on , Right Yellow LED rapid flash to indicate the Master Card had been stored)

3. Press* * to delete the data (1 beep, Left Green LED rapid flash, Right Yellow LED rapid flash)

4. Press # , back to satndby mode

5. Repeat the steps of 10-a to add new master card.

Add New Cards by Master Card

a. -

1. Read master card once (1 beep, Right Yellow LED stay on)

2. Enter slot position 000~999 (Left Green LED stay on, Right Yellow LED rapid flash to indicate the slot position is available)

3. Read new card (1 beep), then enter 4-digit PIN 9999 (1 beep, Right Yellow LED stay on)

4. Press # (1 beep) back to standby mode (Right Green LED stay on)

b. -

1. Read master card once (1 beep, Right Yellow LED stay on)

2. Enter slot position 000~999 (Left Red LED stay on, Right Yellow LED rapid flash to indicate the slot position is unavailable)

3. Press * * to delete the data from the slot position (1 beep, Left Green LED stay on, Right Yellow LED rapid flash)

4. Repeat the steps of 11-a to add new cards

Turn Anti-Tamper Alarm Function ON/OFF

1. Enter programming mode

2. Press * 6 (Right Yellow LED rapid flash)

3. Press 01 ( 1 beep, Right Yellow LED stay on) - function OFF Press 02 ( 1 beep, Right Yellow LED stay on) - function ON

4. Press # (1 beep) back to standby mode (Right Green LED stay on)

Turn Doorbell Alarm Function ON/OF

1. Enter programming mode

2. Press * 2 (Right Yellow LED rapid flash)

3. Press 01 (1 beep, Right Yellow LED stay on) - function OFF Press 02 (1 beep, Right Yellow LED stay on) - function ON

4. Press # (1 beep) back to standby mode (Right Green LED stay on) Note: Turning on doorbell alarm function on the second relay, relay strike time is 1 second.

Reset the Master Code to Default Value

Turn off the power: press # continuously, and energize (1 beep), the master code is reset to default value

Add new cards to Relay 1

1. Enter programming mode, press *9 (Right Yellow LED flash)

2. Press 01 (1 beep, right Yellow LED flash)

3. Select slot position 000~999, press the number of cards (001~999) (1 beep, right Yellow LED flash)

4. Read new cards (in serial order) (1 beep, right Yellow LED flash)

5. Press # (1 beep) back to standby mode (right Green LED stay on)

Change PIN to Relay 1

1. Enter programming mode, press *9 (right Yellow LED flash)

2. Press 02 (1 beep, right Yellow LED flash)

3. Press slot position 000~999

4. Press PIN code (1 beep, right Yellow LED flash)

5. Press # (1 beep) back to programming mode (right Yellow LED stay on)

6. Press # (1 beep) back to standby mode (right Green LED stay on)

Change the length of Master Code

1. Enter programming mode, press *9 (right Yellow LED flash)

2. Press 04 (1 beep, right Yellow flash)

3. Press the length of Master Code (4 ~ 6 digits) (beep…clear PINs and cards) (1 beep)

4. back to programming mode (right Yellow LED stay on)

5. Press # (1 beep) back to standby mode (right Green LED stay on) (After changing the length of Master Code, all PINs and cards will be cleared too. If the length of Master Code is 4 digits, press 1234; if 5 digits, press 12345; if 6 digits, press 123456.)